Migration of pages from the old location http://qyx.krtko.org/projects/ and others is ongoing. Old links should still work though.

tomato-single-cell

A single-cell Li-Ion/Li-Po/LiFePO4 battery solar charger board for the natWatch platform (tomato-series solar chargers)


pio-relay-s4

4 SPDT relay output board for the natWatch platfgorm

OLD uMesh secure mesh network protocol stack

uMesh is a set of experimental communication protocols intended mainly for low data rate wireless mesh networks such as sensor networks for environmental data gathering, asset and people tracking, short message delivery and paging, narrowband voice communication etc. in scenarios, where common network infrastructure is not reachable and/or is not feasible for a particular purpose. Protocols are designed with high level of security in mind which could make them suitable for many critical and disaster recovery applications in the future.


plumCore framework for IoT


OLD uMeshFw Bootloader (uBLoad)

A (slightly more) secure bootloader for (not only) uMeshFw compatible wireless nodes


qdlLibrary

A simple display list rendering library. Main difference from other libraries for drawing objects on a canvas is that here the objects are rendered when display refresh occurs. Objects to be drawn are sorted as a nested boxes (hierarchical structure, tree). This approach uses much less memory and allows drawing on large displays without controller with dedicated display memory. It also makes “redrawing” screen and user interface widgets easier - there is no need to actively redraw anything after changes.


SimpleFlashFileSystem

Simple filesystem originally developed for saving configuration and firmware update images on NOR flash memories in embedded systems. It is based on other similar filesystems (like yaffs, jffs), but it is made even simpler. No filenames or directory structure is supported, files are referenced by their IDs (like on smart cards). Filesystem is optimized for simplicity and is probably unoptimal in every single way.


qNode5 - uMesh debug platform

uMeshFw compatible debug platform with STM32F407 MCU, radio, gps, LiPo accu and large STN transflective LCD display.


qNode4 - uMesh-compatible solar powered low-cost node

First working hardware architecture capable of running uMeshFw. Contains low-cost STM32F401 Cortex-M4 MCU, RFM69 radio, battery step-down converter and solar step-up converter (without MPPT) feeding a LiPo charger.


RF amplifier for the 433MHz band

Amplifier and filter for amateur balloon telemetry reception


Solar power management module

Power management module for solar charging of small capacity LiPo cells controllable over I2C bus. Primarily intended to be used on uMeshFw solar-powered nodes. Although quite funtional, very old and never really used.


LED lamp in a jar

White led driver board enclosed in a glass jar.


GPS tracker with a simple LCD interface

After much negative experience with Android GPS tracking (battery usage, bad reception) I decided to build my own dedicated GPS tracker despite the fact that multiple similar devices are readily available on the market.

No prototype was made.


TreeCli - a hierarchical, tree structured command line parser/interface

Treecli provides a convenient way to configure various embedded devices using common serial and network interfaces. It is inspired by command line interfaces commonly found in network gear (switches, routers, firewalls..).


LineEdit library

Lineedit aims to be a lightweight command line editor usable over common stream interfaces (like sockets, serial ports, etc.). It was written to be used on an embedded platform and its features and code are optimized for embedded environments.


kiwi-simple

2Msps, 4-channel, 1Vp-p, GPS synchronized signal digitizer


plumpot-lp

Low power STM32L4 base board for the natWatch platform with micro-sd slot, QSPI flash


meteo-solar-shield

A circular-shaped base board for low-cost integrated sensors enclosed in a solar shield. It has two A-coded M12 connectors, communicates over the CAN bus and can be supplied with a 3.6-33V power.


2 channel ultrasonic transducer driver and time-to-digital converter


VLF loop antenna preamplifier


Soil moisture sensor with capacitive sensing

A small capacitive sensing soil moisture sensor node based on the STM32L4 MCU with a AX5243 radio transceiver

GPS-synchronized VLF receiver for the purpose of lightning detection and mapping. Project was started long time ago as a possible contribution to blitzortung.org, however it was abandoned later. There are plans to revive it with many improvements compared to the original design. 02/2018 - Part of the project is implemented with the kiwi-basic digitizer


Snow pit profile sensing with TDR


PEEP (Photo-Electronic Erosion Pin) sensors with mesh network radio


Ideas for bulding different NatSense platform enclosures using commonly available plastic and extruded aluminium boxes.

Semantic Versioning for hardware components

After some time using both the SemVer and GitFlow, I decided to try to apply similar rules to hardware development, mainly for system components and PCBs revision marking.


The NatWatch platform specification - A stackable and extensible board platform for nature observation and environmental monitoring

This is an attempt to specify an extensible platform in the hope that it will be useful. A platform built by electronic engineers and enthusiasts for researchers in environmental sciences for nature observation and monitoring. A platform, where the actual user is not required to have soldering skills, does not have to download arduino.exe and handcraft some code, where the devices are able to withstand severe environmental conditions, be reconfigurable and extensible in the field and are made to be useful for the actual intended purpose and not playing. For now, I selected a simple name “NatWatch” for the platform.


An explanation why I decided to investigate wireless mesh networks deeper and initiate the uMesh and plumCore projects - pdf presentation

RFM69(CW) sub-1GHz wireless radio module range testing - part 1 still missing, part 2, part 3


Multi-cell isolated battery voltage monitoring

I was considering multiple options for monitoring large stack of batteries/cells for an off-grid solar application. Recently i came across a very interesting approach described in the AN112 from Linear Technology by Jim Williams and Mark Thoren entitled “A Simple Solution to a Not So Simple Problem”.


  • index.txt
  • Last modified: 2018/09/14 21:19
  • by qyx